Page: 27

Analysis Help
Analysis: Raw trace amplitude vs W.F. level


Displacements measured for each frame, on the trace selected by the "Amplitude trace #", are displayed with respect to corresponding level measurements on the waveform selected by the "Amplitude W.F. #". The trace amplitude measurements are taken the same way they are for the "Raw trace amplitude vs step cycle" graph. The waveform amplitude measurements are taken the same way they are for the "Trace averaging based on W.F. level" analysis. The "Fixed W.F. level bins" option has a slightly different effect here, since the range of levels is not divided into bins, but it may affect (increase) the range of levels displayed to the full range defined by the "Min W.F. amplitude" and "Max W.F. amplitude" parameters.

Deleted frames, and frames whose tag values are not in the "Tag list" are excluded. You can also exclude frames that occur during the inactive phase of cycles, or the active phase, in the same way as for the "Trace averaging based on W.F. level" analysis, using the "Active cycle phase only" option.

 

Key sequence  Parameter Initial Value
<Esc>AGTTR  Analysis method  Raw trace amplitude vs W.F. level
<Esc>SF  Run file  ?
<Esc>SRS  Start of run  0 msec
<Esc>SRE  End of run  2.14748e_08 msec
<Esc>SRD  # of deleted sections  0
<Esc>SCID  Phase selection delay  0 msec
<Esc>SCIW  Phase selection window  0.1 msec
<Esc>SLTA  Active cycle phase only  N
<Esc>SCW  Cycle W.F. #  ?
<Esc>Wn<CR>SCV  Cycle crossings  ?
<Esc>SCS  Base cycles on stop time  N
<Esc>SCT  Base cycles on spike trains  N
<Esc>SLWN  Amplitude W.F. #  0
<Esc>SLWRL  Min W.F. amplitude  -80000 mV
<Esc>SLWRU  Max W.F. amplitude  79997.6 mV
<Esc>SLWF  Fixed W.F. level bins  N
<Esc>SLWD  W.F. amplitude delay  0 msec
<Esc>SLWW  W.F. amplitude window  0.1 msec
<Esc>ST  Tag list  All
<Esc>SLTN  Amplitude trace #  0
<Esc>SLTS  Trace amplitude point  ?
<Esc>SLTR  Trace amplitude ref  -0.1 msec
<Esc>SLTWS  Trace ampl. point window  0.1 msec
<Esc>SLTWR  Trace ampl. ref window  0.1 msec
<Esc>SLTWA  Average trace ampl. ref.  N
<Esc>SLTWD  Trace ampl. ref. regression degree  0
<Esc>SLTWF  Find max trace amplitude  Y
<Esc>SLTWI  Trace ampl. integration  N
<Esc>SLTWM  Average trace ampl. sample  N
<Esc>SLTP  Trace ampl. as % of max  N
<Esc>SLWP  W.F. ampl. as % of max  N
<Esc>SGR  Regression degree  0
<Esc>SDD  Graph description  ""
<Esc>SDM  Main graph title  ""
<Esc>SDGG  Graph type  Adaptive
<Esc>SDGD  Diamond symbol size  5
<Esc>SDGT  Graph tag symbol  ""
<Esc>SDSA  Auto scale  Y
<Esc>SDSR  Round out scale bars  Y
<Esc>SDSXS  X scale bars  Y
<Esc>SDSYS  Y scale bars  Y
<Esc>SDSXL  Min X  0
<Esc>SDSXU  Max X  0
<Esc>SDSYL  Min Y  0
<Esc>SDSYU  Max Y  0
<Esc>SDTT  Top title display  Y
<Esc>SDUL  Sample units  mV

 


SCRC WWW administrator: www@scrc.umanitoba.ca
Copyright © 2017 G. R. Detillieux, Spinal Cord Research Centre, The University of Manitoba.